Anima / MOSS DAVE (after compile):
AnimaDAVE is a model patch for Anima/Cosmos and MOSS-Image that aims to increase variation between images generated from the same prompt. During sampling, it reduces a shared, per-channel component of selected transformer blocks’ activations, generally concentrating the adjustment in the earliest steps. This gives the model more room to produce different results without changing your prompt. The adjustment is applied while the model runs; it does not directly edit a finished image.
Anima / MOSS DAVE (after compile) Input Parameters:
model
The MODEL to patch. Connect a compatible Anima/Cosmos or MOSS-Image model that you intend to use for sampling. The node clones the model and adds its sampling-time adjustment to the clone, leaving the supplied model available for other workflow branches. There is no numeric range or default.
mask
Selects a bundled .npz file containing per-block weights that determine where, and how strongly, the adjustment is applied. The available options are auto plus the .npz files found alongside the node; the exact file list depends on your installation. auto selects the shipped mask for the detected model architecture: dave_alpha.npz for Anima, targeting blocks 8–18, or moss_dave_alpha.npz for MOSS-Image, targeting blocks 19–30. Use auto unless you have a reason to select a particular bundled mask. No explicit default selection is specified in the interface.
strength
Sets the overall dose of the adjustment. The node multiplies this value by each selected block’s mask weight, so blocks can receive different amounts. Higher values apply stronger removal of the shared activation component and are intended to increase same-prompt diversity; 0 disables the adjustment and passes the original model through. The default is 0.30, the minimum is 0.0, the maximum is 1.0, and the adjustment step is 0.01. The node tooltip describes 0.30 as a conservative starting point and suggests values up to approximately 0.80 with tau=0.10 for maximum diversity.
tau
Controls how long the adjustment runs during sampling. When a sampling schedule is available, positive values activate it for approximately this fraction of the earliest, high-noise steps, with at least one step active. The default is 0.06, the minimum is 0.0, the maximum is 1.0, and the adjustment step is 0.01. 0 means the adjustment runs on every step, not that it turns off. If the sampler does not provide a step schedule, the node also runs the adjustment on every step. The node tooltip recommends keeping tau at or below 0.10 because wider windows can disrupt text and hands more than increasing strength does.
Anima / MOSS DAVE (after compile) Output Parameters:
model
The resulting MODEL for your sampler. When the selected mask has active blocks and strength is above zero, this is a cloned model configured to apply DAVE during eligible sampling steps; it is not a generated image. If strength is 0 or the selected mask has no effective weights, the output is the original model unchanged. Connect this output wherever your workflow expects the model to sample from.
Anima / MOSS DAVE (after compile) Usage Tips:
- Start with
mask=auto,strength=0.30, andtau=0.06. Generate multiple images with the same prompt to judge whether the amount of variation suits your project. - If you want more variation, raise
strengthgradually before widening the active step window. Keeptauat or below0.10when text or hands matter. - To compare against an unpatched model, set
strength=0. Avoid usingtau=0for this purpose: it makes DAVE run on every sampling step. - If you also use Anima Block Compile, place AnimaDAVE after it in the model chain so its adjustment attaches to the live blocks used during sampling.
Anima / MOSS DAVE (after compile) Common Errors and Solutions:
DAVE mask not found: <path>
- Explanation: The selected mask file is missing from the node’s mask directory.
- Solution: Select
autoor an available bundled mask. If a shipped mask is missing, restore the node’s installation.
DAVE mask <file> has <number> blocks, the MOSS-Image model has <number>; use mask=auto or moss_dave_alpha.npz
- Explanation: A selected mask has a different number of block weights from the connected MOSS-Image model, so it cannot be applied to that model.
- Solution: Choose
autoor the suggested MOSS-Image mask. Check that the connected model and node files belong to compatible installations.
KeyError: 'weight' or an invalid .npz mask error
- Explanation: The selected mask could not be read as expected, or it does not contain the required
weightarray. - Solution: Switch to
autoand use an intact bundled mask. Restore or replace any damaged mask file.
No visible increase in variation
- Explanation:
strength=0disables DAVE, a mask may have no effective weights, or the change may be subtle at the current settings. An incompatible model layout may also leave no applicable blocks to hook. - Solution: Confirm that you connected the node’s
modeloutput to the sampler, use a compatible model withmask=auto, and test several same-prompt samples. If needed, increasestrengthgradually while keepingtaushort.
Text or hands become distorted
- Explanation: The adjustment may be active for too much of the sampling process; the node specifically warns that wide
tauwindows can affect text and hands. - Solution: Return
tauto0.06or keep it at or below0.10. If necessary, reducestrengthas well.
